A toilet that keeps running is almost always leaking water from the tank into the bowl, either through a worn flapper or because the fill valve will not shut off. Both can be told apart in about 20 minutes with a pencil or a few drops of food colouring. If the part is cheap and accessible, the fix is often simple. If the leak is at the base of the toilet, or the repair does not hold, it is time for a licensed plumber.
This guide walks you through the causes in the order they are most likely, the tests that point to the right one, and the signs that the job has moved beyond the tank lid.
TL;DR
- Most running toilets come from a worn flapper letting water seep into the bowl. Korky explains that the falling tank level then makes the fill valve turn on again, which is the “phantom flush” you hear.
- Tell the flapper from the fill valve with a simple test: mark the tank water level, shut off the supply, and watch whether the level drops.
- Water that keeps flowing after the tank is full points to the fill valve, its float height, or debris.
- Water around the base of the toilet is a different problem, usually the seal under the bowl, and it can damage the floor below.
- If the toilet still runs after a new flapper or fill valve, or you see water on the floor, call a plumber.
Table of Contents
- What is actually happening inside the tank
- Before you touch anything: shut off the water
- Three tests that point to the cause
- The flapper: the usual suspect
- The chain and the handle
- The fill valve: when water runs into a full tank
- Why a toilet randomly runs for a few seconds
- Water around the base of the toilet
- What a running toilet costs
- Our perspective
- When to call a plumber
- Need it fixed today? We can help
- FAQ
- Sources
What is actually happening inside the tank
A toilet tank holds a fixed amount of water. The flapper is a rubber seal at the bottom that lifts when you flush and drops back to seal the tank. The fill valve refills the tank after each flush and shuts off when a float reaches the right height. An overflow tube sits in the middle as a safety drain.
A running toilet means one of these parts is not doing its job:
- The flapper is not sealing. Water trickles from the tank into the bowl. As the level falls, the float drops and the fill valve opens to top it up. Hence the short bursts of running every few minutes.
- The fill valve is not shutting off. Water keeps entering a full tank and spills into the overflow tube.
- The chain or handle is interfering. Something is holding the flapper slightly open.
The City of Calgary’s homeowner guide identifies a worn flapper as the most common culprit for a leaky toilet. That matches what we see on service calls across Greater Vancouver.
Before you touch anything: shut off the water
Every repair below starts the same way. Find the shut-off valve behind or beneath the toilet and turn it clockwise until it stops. Forbes Home notes that some valves need only a quarter turn while others take several turns. If the valve is stiff or rusty, it recommends a lubricant rather than a wrench, because forcing it can break the valve and cause flooding.
Then flush to empty the tank as much as possible. Gerber’s support guidance gives the same order: supply off first, then flush.
If the toilet’s own valve is seized, leaking or missing, you need the main shut-off. Our guide to finding and using your main water shut-off shows where it usually sits in a Vancouver-area home. If that main valve itself drips or will not turn, read what to do when the main shutoff valve is leaking.
Three tests that point to the cause
Do not replace parts by guessing. One of these tests will tell you which part is failing.
The dye test
Remove the tank lid and add several drops of food colouring, or a little coffee or tea. The City of Calgary recommends waiting 15 to 20 minutes without flushing. If colour shows up in the bowl, the toilet valve is leaking. The City of Toronto suggests a similar dye test with a shorter wait of 10 to 15 minutes.
The pencil-mark test
Flush, then draw a pencil line at the waterline inside the tank. Turn off the supply valve and wait. The Municipality of Port Hope describes the result this way: after 20 to 30 minutes, if the level is still at the mark, the leak is likely at the fill valve or ballcock. If it has fallen below the mark, the flapper is the likely culprit.
Korky’s version of this test waits at least 25 minutes. If the level then falls, it advises leaving the water off for a couple of hours. A drop to the flapper or flush seal means replacing that part. A drop to a point on the overflow tube or the bottom of the tank means replacing the flush valve.

The overnight test
Turn the water off before bed. Port Hope’s guide suggests dumping a bucket of water in the bowl if you need to use the toilet overnight. In the morning, if the tank level is lower or even with the edges of the flapper, the flapper or its seat is the likely problem.
| What you see | Most likely cause | Next step |
|---|---|---|
| Dye reaches the bowl | Worn or dirty flapper, or damaged seat | Clean the seat, replace the flapper |
| Level drops after supply is off | Flapper or flush valve seal | Replace the flapper or seal |
| Level stays at the mark after supply is off | Fill valve or ballcock | Adjust, clean or replace the fill valve |
| Running stops only when you jiggle the handle | Chain, handle or flapper catching | Adjust the chain and handle |
| Water on the floor at the base | Seal under the bowl, or a cracked bowl | Stop using the toilet and call a plumber |
The flapper: the usual suspect
Over time, rubber flappers go hard, warp or collect mineral deposits. Calgary’s guide gives a quick check: rub the underside of the flapper with your finger. Streaks of rubber, or a flapper that has gone from soft and flexible to hard, means it needs replacing.
Pressing down on the flapper with the water running is another clue. If the running stops, the flapper was not sealing.
How to replace a flapper
Calgary’s guide describes the process this way:
- Shut off the water and flush the tank.
- Note how long the chain is between the handle arm and the flapper.
- Remove the old flapper and fit the new one.
- Return the chain to its original length.
- Check the valve seat for corrosion or mineral buildup. Clean it and sand it smooth with fine sandpaper.
- Turn the water back on and repeat the leak test.
Bring the old flapper to the hardware store so you match the size. Flush valves differ, and a flapper that fits badly will leak just like a worn one. Some, such as Fluidmaster’s 502 PerforMAX, are made to fit most 2-inch flush valves.
Keep bleach tablets out of the tank
Drop-in bowl cleaners that contain bleach or chlorine sit in the tank water all day. Fluidmaster Canada warns that these products damage tank components and may cause flooding and property damage. If your flapper keeps failing within a year or two, an in-tank cleaner is a common reason.
The chain and the handle
If the toilet runs until you jiggle the handle, the flapper is probably being held open or prevented from dropping. Calgary’s guide lists the likely causes: the chain may need adjusting, may be caught on something, or may have a kink. A kinked chain should be replaced with a ball-type chain. The nut holding the handle may need tightening, or the handle may need replacing.
Slack matters in both directions. Korky advises leaving only one to two links of slack so extra links do not fall into the drain opening and stop the flapper from seating. Too tight, and the flapper never fully closes.
The fill valve: when water runs into a full tank
Watch the tank as it refills after a flush. If water keeps flowing once the tank is full, and the flapper is sealing, the fill valve is the problem. Korky says the float may be set too high, clogged with debris or failing to shut off. Adjusting, cleaning or replacing the fill valve fixes a constantly running toilet in these cases.
Check these in order:
- Water level versus the overflow tube. Water spilling into the overflow tube means the level is set too high. On a float-cup model, Danze’s manual says to lower the level by turning the adjustment rod to move the float cup.
- Fill valve height. Korky says the fill valve should sit below the top of the overflow tube, locked in place after adjusting. When fitting a new one, set the water level mark about half an inch below the top of the overflow tube. Too high and it will not shut off. Too low and the flush is weak.
- The refill tube. Make sure it is not pushed down into the overflow tube, which can create a siphon.
- Debris. Rona notes that debris can stop the shut-off mechanism from working, so the valve may only need cleaning. If it is an older ballcock model, replacing it is a chance to upgrade.
If the toilet is noisy rather than running, Danze’s manual says debris inside the valve head may be causing vibration. It suggests cleaning it, and partly closing the supply stop if incoming flow is excessive, aiming for a tank refill of roughly 60 seconds.
Why a toilet randomly runs for a few seconds
This is the question behind most late-night searches. You hear the tank refill though nobody flushed. As Korky explains, the fill valve turning on does not mean it has failed. A worn flapper or flush valve seal lets water leak slowly into the bowl, the float drops, and the valve tops the tank up. Replacing the flapper or seal usually ends it.
If you replaced the flapper and it still happens, Rona says the entire valve assembly may need replacing. Gerber’s guidance adds that visible damage to the flush valve means the assembly itself needs replacing.
Water around the base of the toilet
A toilet that runs and a toilet that leaks at the base are separate problems, and the second is more urgent. Water on the floor can soak subfloor and travel to the ceiling below.
Rona’s guide says that if water appears where the toilet meets the floor, or there are water stains on the ceiling below, you should inspect the base for cracks. A cracked bowl may require replacing the bowl or the entire toilet. The mounting bolts, the anchor flange and the wax seal between the waste pipe and the toilet also need inspection, and any damaged parts replaced.
A few points about the wax seal:
- Oatey Canada notes that wax rings are single use. Once compressed, a ring cannot be reused if the toilet is lifted and repositioned.
- Cold wax is harder and seals less effectively, so the ring should be at room temperature at installation.
- Port Hope’s guide says a damaged gasket under the flapper valve can also show up as water on the floor around the base, so a wet floor is not always the wax ring.
Until the toilet is repaired, stop flushing it and shut off its supply. If water has already reached a ceiling below, our guide to three tests for a bathroom ceiling leak helps you trace it, and our temporary fixes for plumbing leaks covers how to limit damage while you wait for a technician.
What a running toilet costs
A constantly running toilet wastes water around the clock, and the amount can be large. The City of Toronto states that a leaky toilet can waste up to 20 cubic metres a day, which at Toronto’s water consumption charges comes to $97.26 a day. Those figures are the worst case and use Toronto rates. Your own cost depends on your municipality’s rates and how bad the leak is, so look at your water bill or meter.

You can check without any dye. Toronto suggests turning off all taps and watching the meter’s flow indicator. If it moves, water is leaking somewhere. Metro Vancouver homes billed by meter will see the effect directly, and homes on flat-rate billing still waste water and put load on the sewer system.
Our perspective
Most running toilets we are called to are not mysteries. The flapper is worn, the chain is out of adjustment, or the fill valve is dirty or set too high. Those are small parts, and homeowners can often deal with them.
What brings people to us is what happens next. The new flapper does not stop the running because the valve seat is pitted. Or the fill valve was replaced and the real problem was a leak at the base that has been soaking the subfloor for months. A running toilet is a quiet warning, and the point of a proper diagnosis is to find everything behind it, not just the noisy part.
When we come out, we give you clear pricing before we start, our technicians are certified, and our work is backed by a satisfaction guarantee. If the toilet is one symptom of a bigger issue, such as a drain that backs up or a leak elsewhere in the house, we can inspect it on the same visit, including a sewer camera inspection when the drain line is in question. We are available 24/7, because a leaking bathroom does not wait for business hours.
Austin
When to call a plumber
Simple checks are worth doing first, and so is knowing when to stop. Port Hope’s guide advises contacting a licensed plumber right away when a leak is found. Call one in these situations:
- The toilet still runs after you replace the flapper, chain or fill valve.
- The flush valve is visibly cracked or damaged.
- There is water on the floor around the base, or stains on the ceiling below.
- The shut-off valve will not close or leaks when you turn it.
- The toilet rocks or the bowl is cracked.
- You are a tenant or a property manager. Report it promptly so repairs are handled properly and your water use does not climb.
If you are weighing whether a call is worth it, our guide on three questions to ask before calling a plumber walks through the decision. If your toilet has other problems, such as weak flushing, see how to diagnose a toilet that will not flush.
Need it fixed today? We can help
High Pressure Mechanical handles residential and commercial plumbing across Vancouver, Richmond, New Westminster, Burnaby and the North Shore. That includes fixture installation and repair, leakage prevention, general troubleshooting and water damage work, with 24/7 availability for emergencies. We have more than 20 years in the Vancouver market.

See everything we do on our plumbing services page, or reach out through our Vancouver plumber page to book a visit.
FAQ
Why does my toilet run for a few seconds and then stop?
Usually a worn flapper is letting water seep slowly from the tank into the bowl. When the tank level drops, the fill valve opens briefly to refill it. Replacing the flapper or flush valve seal usually stops it.
How do I know if it is the flapper or the fill valve?
Mark the tank water level with a pencil, shut off the supply and wait 20 to 30 minutes. If the level falls, the flapper or flush valve seal is leaking. If it stays at the mark, look at the fill valve.
Does a running toilet increase my water bill?
Yes, because it wastes water continuously. The City of Toronto says a leaking toilet can waste up to 20 cubic metres a day in the worst case. The actual cost depends on how bad the leak is and your local water rates.
How do I turn off the water to my toilet?
Turn the oval handle of the shut-off valve behind or below the toilet clockwise until it stops. Then flush to empty the tank. If the valve will not close, shut off the main water supply and call a plumber.
Why is there water around the base of my toilet?
Common causes include a failed wax seal, loose mounting bolts, a cracked bowl, or a damaged gasket under the flapper. Stop using the toilet, shut off its supply and have a plumber inspect it before the floor is damaged.
Sources
- Toilet Leaks and Repair, City of Calgary
- Water Leaks and Usage, Municipality of Port Hope
- Water Leaks: Costs and How to Spot a Leak, City of Toronto
- How to Fix a Running Toilet, Korky
- How to Replace Toilet Fill Valve, Korky
- My Toilet Flush Valve Does Not Close Properly, Gerber
- 502 PerforMAX Adjustable Flapper, Fluidmaster Canada
- How to Fix Common Toilet Problems, Rona
- Homeowner Care Manual, Danze
- How To Shut Off Toilet Water Supply, Forbes Home
- Wax vs Non-Wax Toilet Seal, Oatey Canada
No comments yet.