Hot water that comes and goes almost always traces back to one of a short list of causes: another tap or appliance stealing hot water, a cracked dip tube, a failed lower element or thermostat on an electric tank, a tankless unit that is not seeing enough flow, or a valve problem. Which one you have depends on when the water changes temperature. This guide helps you read the pattern, run the checks that are safe for a homeowner, and know the point where a licensed plumber should take over. If you are in Vancouver, Richmond, New Westminster or nearby, our plumbers at High Pressure Mechanical handle hot water tank service and water heater repair and replacement around the clock.
TL;DR
- Note the pattern first: sudden swings point to a failed part or a competing demand, while a slow decline points to sediment or a change in how your household uses hot water.
- The most common cause of changing temperature is another demand elsewhere in the house, such as a washing machine or dishwasher drawing water while you shower.
- A cracked dip tube, a failed lower element or thermostat (electric tanks) and low flow through a tankless unit are the next suspects.
- Safe checks stay outside the heater: breaker, thermostat setting, status light, vents, and a look for drips. Never open gas controls or burner compartments.
- A dripping relief valve, a gas or burning smell, a leak, or a breaker that trips again are calls for a licensed plumber, not more resetting.
Table of Contents
- Start with the pattern, not the part
- Another demand in the house
- A cracked or broken dip tube
- Electric tanks: lower element and thermostat
- Tankless heaters: the hot, cold, hot cycle
- Mixing and fixture problems
- Sediment and slow decline
- The relief valve and expansion tank
- Safe checks you can run in ten minutes
- When to stop and call a licensed plumber
- Repair or replace?
- Our perspective
- Get your hot water steady again
- FAQ
- Sources
Start with the pattern, not the part
Before you touch anything, spend one day watching the symptom. Write down what you were doing, which tap you used, and how long the change lasted. That short log narrows the cause faster than any guess.
| What you notice | Most likely area | First safe step |
|---|---|---|
| Hot, then cold for a few seconds, then hot, only when something else runs | Competing demand elsewhere in the house | Stop other water use and retest |
| Lukewarm water at every tap, all day | Cracked dip tube or mixing fault | Compare tank outlet and tap temperature by hand, carefully |
| Hot water for a short time, then cold (electric tank) | Failed lower element or lower thermostat | Check the breaker and thermostat setting |
| Hot, cold, hot during use (tankless) | Flow too low to keep the burner or element active | Open more fixtures or clean the inlet screen |
| Worse in winter | Colder incoming water | Expect shorter supply; get the heater assessed |
| Drips from the discharge pipe | Relief valve or thermal expansion | Note when it drips, then call a plumber |
A sudden change suggests a part has failed. A gradual decline suggests sediment buildup or a change in how many people are using hot water.
Another demand in the house
The Spruce names another water demand elsewhere in the house as the most common cause of inconsistent water temperature. When a toilet flushes, a dishwasher fills or a second shower opens, pressure and the hot-to-cold balance shift at the tap you are using.
To test it, pick a time when nothing else is running, take a shower or run the kitchen tap for several minutes, and see if the temperature holds. Then repeat while a family member runs another fixture. If the swing only appears in the second test, your water heater is probably fine and the issue is the balance of your fixtures, not the tank. In older Vancouver-area houses and in multi-unit buildings, shared supply lines make this even more noticeable.

A cracked or broken dip tube
Inside a tank-type heater, cold water enters through a long tube (the dip tube) that sends it to the bottom of the tank, while hot water is drawn from the top because hot water rises. The Spruce explains that a crack or hole in the dip tube lets cold water mix with hot water near the top, so you get inconsistent or lukewarm water throughout the home. The same article notes the tube can be replaced for far less than a new water heater.
The giveaway is that the problem affects every hot tap, not one fixture, and that the tank seems to “run out” sooner than it used to. Replacing a dip tube means draining the tank and working with the plumbing connections, so it is a job for a plumber. Once the tank is open, a technician can also see whether the tank is otherwise worth keeping, which brings us to age. Our guide on water heater lifespans and plumber checks explains what to weigh.
Electric tanks: lower element and thermostat
On an electric tank, the upper element heats only the top of the tank. HSM University’s Canadian trade course on water heater troubleshooting states that “some hot water but it runs out quickly” is usually a failed lower element or lower thermostat. That matches a common household story: the first few minutes are hot, then the water turns cold and stays cold.
What you can do safely is limited to the outside of the unit:
- Check that the breaker or disconnect is on. If it has tripped, reset it once. If it trips again, stop. Repeated trips are a symptom of a fault such as a stuck thermostat, a grounded element or a loose connection, not something to keep resetting.
- Look at any status light or error code and compare it with the manual.
- Confirm the temperature setting has not been moved.
Testing elements and thermostats involves live electrical parts, so that belongs to a licensed professional.
Tankless heaters: the hot, cold, hot cycle
Tankless units heat water only while water flows. The same HSM University lesson explains that hot, then cold, then hot during use is typically flow falling below the minimum needed to activate the unit. Low-flow fixtures and a clogged inlet screen are the usual reasons. It also describes the “cold-water sandwich”: a slug of cold water that reaches you between two draws when you shut a tap off briefly and turn it back on.
What helps:
- Open the tap a little further, or avoid fixtures with very low flow, to see if the cycle stops.
- Pay attention to whether the problem is worse in winter. The course notes that colder incoming water needs a greater temperature rise, so a unit that coped in summer can struggle in January.
- Ask about descaling. Scale reduces heat transfer and flow. Our article on tankless descaling in Vancouver covers how and when to do it.
Mixing and fixture problems
If the water at the tank outlet is hot but the water at the tap is lukewarm or swinging, the problem may sit between the heater and the fixture. A shower valve cartridge, a mixing valve or a cross-connection (where hot and cold lines are unintentionally joined) can all change the temperature you feel without the heater being at fault. A plumber can isolate this quickly by testing at the tank and at the fixture. That is why a single-fixture problem should be treated differently from a whole-house one: if only the upstairs shower misbehaves, start with that valve rather than the heater.
Our team handles fixture installations and repairs as well as hot water tank service, so one visit can cover both ends of the pipe.
Sediment and slow decline
If the problem built up over months rather than appearing overnight, sediment is a prime suspect. Trudeau Meter describes sediment as insulation in the wrong place: scale on the tank bottom or on an element makes the heater work harder, which shows up as longer recovery times and running out of hot water during busy mornings.
Two practical signs of improvement after service are clearer water when you fill a glass from the hot tap, and a shorter wait for hot water to recover between showers. Routine flushing and inspection is the point of regular service, and we explain it in the real role of water heater maintenance for homeowners.
The relief valve and expansion tank
A dripping pipe near the top of a tank is not a normal quirk. John Wood’s Canadian water heater manual states that temperature and pressure relief valves must be certified to CSA 4.4 in Canada, must never be capped, blocked or plugged, and that a dripping or leaking valve must be repaired by a licensed plumber.
The same manual explains that periodic discharge can be caused by thermal expansion in a closed system, for example where a check valve sits at the water meter. It can be addressed with a diaphragm expansion tank of at least 5.7 L per 190 L of stored water. If your system has an expansion tank, the precharge matters. See our guides on sizing and precharging a water heater expansion tank and what to do about an expansion tank leak.
The same manual warns that setting the thermostat above the 49 °C (120 °F) mark raises the risk of scald injury. So raising the temperature to fight a lukewarm tap is not a safe fix, especially with children or older adults at home.

Safe checks you can run in ten minutes
Good owner checks share three traits: they do not open gas controls or burner compartments on a lit heater, they do not involve live electrical parts, and you can undo them. Within that limit:
- Retest with other water use stopped. This rules out the most common cause.
- Check the breaker once (electric heaters). Stop if it trips again.
- Read the status light or error code against your manual.
- Confirm the thermostat setting has not been bumped, and do not go past the 49 °C (120 °F) mark.
- Look at the outdoor vent (gas or high-efficiency units) and clear snow, ice or debris from the terminal. Do not reach into the vent.
- Watch the discharge pipe. Put a bucket under it and note when it drips.
- Dry the tank and fittings with a towel, then watch where moisture comes back.
- Compare clarity. Run hot and cold water into two white cups and look for discolouration or particles in the hot one.
If the changing temperature comes with water on the floor, shut the supply and follow a plumbing emergencies checklist for stopping the water safely until help arrives.
When to stop and call a licensed plumber
Call right away, and do not keep troubleshooting, if you notice any of the following:
- A gas smell, burning smell or smoke. Leave the home and call the emergency number and your gas utility first.
- Water leaking from the tank, fittings or the discharge pipe.
- A breaker that trips again after one reset.
- A relief valve that drips or has been blocked.
- Rumbling, popping or a sudden drop in hot water together with discoloured water.
- Any need to remove covers, open burner compartments or bypass a safety control.
For a boiler-based hot water system, the warning signs are different. Our guide to the signs a boiler needs immediate repair lists them.
Repair or replace?
A dip tube or element is a modest repair. A tank that is old, leaking or repeatedly failing is a different conversation, because each repair buys less time. A plumber can look at tank age, the condition of the tank, and whether the symptom matches a single failed part, then give you a clear recommendation. If replacement makes sense, see our page on water heater replacement in Vancouver. For commercial buildings with larger systems, the causes overlap but the stakes are higher; our piece on commercial water heater problems covers them.
Our perspective
Most intermittent hot water calls come down to one question: is the problem the heater, or is it everything after the heater? Homeowners often replace a tank because the water turns cold, when the real fault was a dip tube, a lower element or a fixture valve. Others keep resetting a breaker for weeks.
That is why we start by asking when the water changes temperature, which fixtures are affected and what kind of heater you have. We are certified technicians, we are available 24/7, and we keep our pricing transparent with no hidden fees, so you know what the visit involves before work begins.
If your hot water is unpredictable, you do not need to guess between a repair and a new tank. Have a plumber look at the whole picture, from the heater to the tap, and fix the cause once.
Austin
Get your hot water steady again
High Pressure Mechanical provides water heater service, repair and replacement, along with hot water tank service, drain cleaning, leakage prevention and general troubleshooting for homes and businesses across Greater Vancouver, including Richmond, New Westminster and Burnaby. We back our work with a satisfaction guarantee.

If your hot water keeps swinging, book a plumber through our services page and tell us what you noticed in your log: which tap, what time, how long. It helps us arrive with the right parts.
FAQ
Why does my hot water go hot and cold during a shower?
The most common cause is another demand elsewhere in the house, such as a flushing toilet or a running appliance. If it happens with nothing else running, suspect a cracked dip tube on a tank heater, or low flow on a tankless unit that causes it to switch off and on.
Why is my electric water heater giving intermittent hot water?
A failed lower element or lower thermostat is a usual cause, since the upper element heats only the top of the tank. Check the breaker once and the thermostat setting. If it trips again or the water stays cold, a licensed plumber should test the electrical parts.
Why is my hot water worse in winter?
Incoming water is colder in winter, so the heater has to raise the temperature further. Tankless units in particular can struggle during high demand. A service visit can confirm whether the unit is working as it should or has scale buildup.
Can I turn up the thermostat to fix lukewarm water?
It is not a safe fix. Manufacturer guidance warns that settings above the 49 °C (120 °F) mark increase scald risk, and a higher setting will not cure a dip tube, element or valve fault. Have the cause found instead.
Is a dripping pipe on the tank an emergency?
Treat it as a call to a licensed plumber. A dripping relief valve must be repaired by one, and it should never be capped or plugged. Note when it drips, because that helps identify whether thermal expansion is involved.
Sources
- How to Fix Inconsistent Water Temperature, The Spruce
- Water heater troubleshooting: gas, electric and tankless, HSM University
- Atmospheric Vented Water Heater manual, John Wood
- How to Flush a Water Heater to Reduce Sediment, Trudeau Meter
No comments yet.