The most common signs of pipe corrosion are blue-green stains around fixtures, brown or orange water, a metallic taste, falling water pressure, pinhole leaks and flaking or crusty buildup on exposed pipes. Some show up at the tap, some only on the pipe itself. Some, like condensation, look like corrosion and aren’t. This guide shows you how to read each sign, which pipe material it points to, when it becomes a health question, and when to call a licensed plumber.
TL;DR
- Blue-green stains and blue-tinted water point to corroding copper. Rust-colored water, flakes and falling pressure point to galvanized steel.
- Corrosion itself is not the direct health problem. The concern is that it can release lead and copper into your water, so test before you assume.
- Dark or damp patches on the outside of a pipe can be condensation. Look at the pattern before you decide.
- Pinhole leaks, green crust at joints and pipes over about 20 years old call for a professional assessment, ideally with a camera inspection for buried lines.
- Partial fixes rarely settle a pipe that is corroding throughout. Ask for the condition of the whole run before you approve work.
Table of Contents
- What corrosion actually is, and why it happens in homes here
- Signs you notice at the tap
- Signs you see on the pipe itself
- Is it corrosion, or is it condensation?
- When corroded pipes become a health question
- What to do the day you spot the signs
- Perspective: why we treat corrosion as a whole-system question
- Repair or replace: how to decide
- What water suppliers handle and what you handle
- Prevention that actually helps
- When to call us
- FAQ
- Sources
What corrosion actually is, and why it happens in homes here
Corrosion is the slow chemical breakdown of metal pipe by the water inside it (and sometimes by moisture outside it). Health Canada lists the water characteristics that drive copper corrosion: pH, alkalinity and chloride levels, plus pipe age and microbiological activity.

That matters in Greater Vancouver, where the source water is naturally soft and slightly acidic. Metro Vancouver’s own corrosion control fact sheet from April 2021 describes a plan to raise the region’s water pH from 7.7 to a target of 8.3 to 8.5. Its stated aims include fewer copper pipe leaks and fewer green stains on tubs, sinks and grout. In other words, the region itself treats copper corrosion and green staining as a known local issue.
What happens inside your walls still depends on your pipe material, its age and how it was installed. So the signs below are organized by where you will notice them.
Signs you notice at the tap
These are the clues most people see first, because water carries the evidence to you.
Discolored water
Brown, orange, yellow or reddish water often means iron or steel is rusting somewhere in the system. Blue or green tints suggest copper. Health Canada’s guidance on controlling corrosion says discolored water should prompt sampling for lead and other metals, not just a shrug and a longer run of the tap.
The pattern gives you the first diagnosis:
- Only after the water has sat overnight, then it clears: the problem is likely in your own plumbing.
- Hot tap only: look at the water heater, its anode rod and sediment before blaming the pipes.
- Every tap, all day, and your neighbors see it too: this is more likely a municipal main event, such as flushing or construction work.
We wrote a step-by-step brown tap water checklist that walks through those tests in about five minutes.
Blue-green stains on fixtures, tubs and hair
Copper corrosion releases copper into the water. Health Canada notes that corrosion can cause pitting and pinhole leaks, and that copper in water can produce blue water that stains bathroom fixtures and hair. If you see a turquoise ring under the faucet or a green tint in blond or light-colored hair, the copper in your system is dissolving.

A metallic taste or smell
A coin-like or bitter taste, especially first thing in the morning, suggests metals dissolving into standing water. Taste is not a reliable measure of how much lead or copper is there. Lead has no useful taste at all, which is why the next section matters.
Low or uneven water pressure
Galvanized steel pipe corrodes from the inside out. A municipal service tubing presentation describes how this narrows the pipe, reducing flow, and how older galvanized lines can develop rust-colored flakes and lose pressure over time. If one fixture is weak and the others are fine, check the aerator first. If pressure has dropped across the house over years, suspect narrowing pipes.
Signs you see on the pipe itself
If you have a basement, crawlspace or utility room with exposed pipe, a ten-minute walk with a flashlight tells you a lot.
On copper pipe
- Green or blue crust at joints and fittings. Green discoloration on the outside of copper can indicate a leak, according to a Canadian home-owner guide on copper plumbing. Fresh, damp crust means active seepage.
- Black discoloration. The same guide says black marks anywhere on a copper pipe often signal corrosion, possibly from water pH that is too high or too low.
- Pinhole leaks. Tiny sprays or pinpoint wet spots along the pipe wall, not at a joint, point to pitting from the inside.
- Age. BC Housing’s leak prevention bulletin says copper can corrode as it ages, depending on production quality and local water minerals. For copper over 20 years old, it advises investigating the condition and starting a replacement plan.
On galvanized steel pipe
Galvanized pipe is zinc-coated steel, common in older homes. Visible clues include rust-colored water, rough or flaking surfaces, and compression patches. A Canadian home inspection reference describes these clamps and patches as temporary fixes often applied once the pipe has started to rust through. If you find several on one run, the pipe is telling you the rest of it is likely thin too.

On drain lines
Cast iron and steel drain, waste and vent pipes corrode too, and they hide it better. Slow drains in more than one fixture, gurgling, recurring backups, sewer odors and damp spots on ceilings under bathrooms are the typical symptoms. A drain that keeps clogging after cleaning may be rough or scaled inside, or partly collapsed. A sewer camera shows which, which is why we recommend it before anyone quotes you for relining or replacement. Our piece on insisting on CCTV before relining or replacement explains what you should see in the footage.
Pipe insulation worth checking
If your house was built before 1990, old pipe wrap can hide the pipe’s condition and may itself be a hazard. Before cutting into any insulation, read how to identify asbestos pipe wrap and leave suspect material alone until it is tested.
Is it corrosion, or is it condensation?
Not every wet or dark pipe is corroding. Cold water pipes in a humid basement sweat, and the moisture can stain, flake paint and even rust the outside surface. A home inspection reference notes that dark stains on the outside of a galvanized pipe do not necessarily mean internal corrosion, since condensation can cause flaking or staining.
A few ways to tell them apart:
| What you see | More likely condensation | More likely corrosion or a leak |
|---|---|---|
| Moisture pattern | Even droplets along a long cold pipe | Wet spot at one joint, fitting or pinhole |
| Hot water pipes | Dry | May show crust or stains |
| Timing | Worse in humid weather, gone when dry | Constant, or growing |
| Color | Light rust film on the surface | Green, blue or white crust; black patches |
| Water at the tap | Normal | Discolored, metallic or low pressure |
The drip pattern is also described in a Canadian renovation guide on cold-pipe condensation: uniform droplets on a long cold pipe suggest condensation, while moisture localized at a joint is a different condition to assess. Wipe the pipe dry and check again in an hour. If wetness returns at exactly one spot, treat it as a leak.
The only sure way to know what a galvanized pipe looks like inside is to cut out a sample and examine the walls and buildup. That is a job for a plumber, not a weekend experiment.
When corroded pipes become a health question
Health Canada’s position is worth stating precisely. It reports there are no direct health effects from corrosion itself, but corrosion can release contaminants such as lead and copper into drinking water at levels of concern. Lead is the one to take seriously.
Health Canada explains that older homes may have lead service lines (permitted until 1975) or lead-based solder (permitted until 1986). It also gives a simple field check: pipes that look greyish-black and are soft enough to dent or scratch with a knife may be lead. If you find one, stop poking at it and get your water tested.
Its Water Talk on lead stresses that measuring lead at the tap is the critical step in assessing risk. You cannot see, taste or smell it, so discolored water or visible corrosion in a pre-1990 home is a reason to sample, especially if anyone in the house is pregnant, bottle-feeding or a young child. For test options and what the results mean, talk to your local health authority or an accredited lab.
What to do the day you spot the signs
- Flush before drinking. Health Canada advises running the cold tap until the water is cold before using it, especially after it has sat for hours.
- Use cold water only for cooking and drinking. Hot water leaches more lead and other metals from plumbing, according to the same page.
- Photograph what you see. Pipe, joint, stain, tap water in a clear glass. Dates help a plumber judge whether a problem is growing.
- Check for active leaks. Dry the pipe, look again in an hour, and check the ceiling and cabinets below.
- Test for lead if your home is older. A lab test of first-draw water is the only way to know.
- Book a professional assessment. BC Housing is clear that plumbing repairs should be done by a qualified professional rather than as DIY.
If you see water spraying, a ceiling bulging or a pipe weeping steadily, shut off the main valve first, then call. That is an emergency, not a scheduling question.
Perspective: why we treat corrosion as a whole-system question
Our view is shaped by what we see in Greater Vancouver homes, from heritage houses in New Westminster to newer builds in Richmond. A visible green patch or a pinhole leak is rarely a single-spot problem. It is the first place the pipe gave up, and the rest of the run often has the same wall thickness and the same water chemistry acting on it.
That is why we push for evidence before a decision. A camera on the drain lines, a look at the water heater, a review of the pipe material and age, and an honest answer on whether a spot repair buys years or just weeks. Homeowners often hear two options, patch it or rip everything out, when the right answer is a staged plan. We also think older houses deserve extra care; see our notes on plumbing failures in heritage homes for how age and original materials change the picture.
No one should be sold a replacement because of a scary photo, and no one should be told a corroded pipe is fine because it hasn’t leaked yet.
— Austin
Repair or replace: how to decide
A small, isolated leak at a fitting on otherwise healthy copper can often be repaired. Widespread signs usually change the answer: multiple pinholes, green crust at several joints, rust-colored water throughout the house, or galvanized steel that has narrowed enough to cut flow.
Some pointers:
- Lead service lines: Health Canada recommends full replacement as the most effective and permanent solution and generally advises against partial replacement. The service line connects the street main to your home, so coordinate with your municipality.
- Pipes over 20 years old with symptoms: BC Housing’s guidance on copper is to investigate condition and begin a replacement plan, not to wait for a failure.
- Buried drain lines: get footage first. Cleaning, relining and replacement suit different defects, and the camera tells you which one you have.
- Hot water tank corrosion: if the tank, not the pipes, is rusting, replacement of the tank may solve it. Our boiler repair versus replacement article covers the same logic for heating equipment.
Cleaning does not undo corrosion. Descaling or hydro-jetting can clear buildup from a drain and restore flow, but it cannot restore lost metal. If the wall is thin, cleaning may even expose a weak point. That is why a diagnosis comes first.
What water suppliers handle and what you handle
In BC, the province’s drinking water design guidelines refer to the Guidelines for Canadian Drinking Water Quality and include objectives for stable, non-corrosive water. Suppliers are responsible for water quality up to the property. Inside the property, the pipes, solder, fixtures and tank are yours.
That split explains why two neighbors can see different results. Pipe material, age and plumbing layout differ house to house, even on the same street and the same water.
Prevention that actually helps
- Walk the pipes once a year. BC Housing recommends owners responsible for plumbing check joints and connections annually for cracks and leaks.
- Control basement humidity so condensation doesn’t mask real problems or rust fittings.
- Flush stagnant water after vacations or long absences.
- Know your materials. Find out whether you have copper, galvanized steel, plastic or something older, and when it was installed.
- Keep the water heater serviced. Sediment and anode wear affect hot-side corrosion.
- Schedule routine maintenance so small problems get found early. Our guide to plumbing maintenance best practices lists a practical yearly routine, and our common plumbing problems in Vancouver homes article shows what we see most often locally.
When to call us
If you see green crust, pinhole leaks, rust-colored water or falling pressure, we can inspect the pipes, check drain lines with a sewer camera, assess your water heater and tell you plainly whether the problem is spot or systemic. We work 24/7 across Vancouver, Richmond, New Westminster and neighboring Greater Vancouver communities, with certified technicians and transparent pricing.
See our plumbing, drain cleaning and leakage prevention services or reach us through our Vancouver plumber page to book an assessment.
FAQ
How can I tell if my pipes are corroded?
Look for blue-green stains, rust-colored or blue-tinted water, a metallic taste, falling pressure and green or black crust at joints. Then rule out condensation by checking whether the moisture is even along the pipe or concentrated at one spot. If your home predates 1990, consider testing your water for lead.
Can a corroded pipe be repaired?
Sometimes. A single leak on otherwise sound copper can be repaired, but widespread corrosion usually means replacing the affected run. For lead service lines, Health Canada recommends full replacement rather than partial. A plumber’s inspection should tell you which situation you are in.
What gets rid of corrosion on pipes?
Surface deposits on exposed pipe can be cleaned, and drain buildup can be cleared by hydro-jetting. None of that restores metal already lost from inside the pipe wall. If the pipe is pitting or leaking, the lasting fix is repair or replacement by a qualified professional.
Do corroded pipes need to be replaced?
Not always, but pipes with multiple pinholes, galvanized lines with falling pressure and copper over 20 years old with symptoms are strong candidates. BC Housing advises investigating older copper and starting a replacement plan. A camera or pipe sample gives you evidence to decide.
Sources
- Health Canada: Guidance on sampling and mitigation measures for controlling corrosion
- Health Canada: Copper in drinking water
- Health Canada: Reduce your exposure to lead
- Health Canada: Water Talk on lead in drinking water
- BC Housing: Maintenance Matters 21, Preventing Water Leaks
- Metro Vancouver: Corrosion Control Program fact sheet
- Government of BC: Design guidelines for drinking water systems
- Municipal service tubing presentation
- Copper pipes and plumbing at home
- Galvanized plumbing reference
- Condensation on cold-water pipes
No comments yet.